Why is My Geek Bar Flashing Red 8 Times
Table of Contents Preview
Battery - Related IssuesCharging - Related Problems
Hardware - Related Faults
E - Liquid - Related Concerns
If you use the popular vaping device Geek Bar and see a red light flashing eight times, this can be very alarming. This unique flashing design should be a give away that something is wrong with your device. The only way to tackle that problem is to figure out what the root causes are. We will take a deep dive into the possible reasons for the Geek Bar flashing eight times red and what to do about it in this article.
Battery - Related Issues
1-1 Low Battery Charge
This is one of the more common reasons for your Geek Bar to flash red eight times which is an indication of a critically low battery charge. Like many of its electronic counterparts the Geek Bar relies heavily on its battery to work well. This is the very flashing sequence your device is programmed to show you when its battery level is getting dangerously low.
The battery in Geek Bars has a limited capacity, and using it constantly will eventually deplete it. If you have recently been using your Geek Bar a lot without putting your Geek Bar down for any period of time, this means that the battery will start to charge and get low enough for it to no longer be able to power the actual device. This eight - time red flashing means a battery charge is immediately required.
To check if this is the issue just plug your Geek Bar into a compatible charger. Also, if the device starts charging showing a different flashing pattern or a constant light, then it is confirmed that the battery was low.
1-2 Battery Malfunction
But it isn't always about a low charge. In some cases, the battery in itself can be damaged. Batteries can deteriorate over time due to many reasons including overcharging high temperatures or the normal ageing associated with repeated charge - discharge cycles.
Extreme temperatures hot and cold alike can also damage the battery and cause aberrant behavior. Leaving your Geek Bar in a hot car in summer or in a cold outdoor environment for their maximum time is going to affect the performance of a battery.
A faulty battery may not charge as good as it once did or may not provide the required voltage to the device. But in such cases, red eight - time flashing may follow even after charging. If you have a model with removable battery, please do this test by replacing the battery and confirm whether the battery is defective or not. If putting in the new battery resolves the issue then the original battery is at fault.
Charging - Related Problems
2-1 Faulty Charger or Cable
The red eight - time flashing can also be caused by a problem with the charger or charging cable. If the charger does not give the right voltage and current to the device then Geek Bar can not be charged which activates the warning signal.
The charger may have suffered a physical damage including damaged power adapter or loose connection. Similarly the charging cable can be worn down or a bent or broken internal wire. These problems cause a disruption in flow between the charger and the device.
If none of that worked visually inspect the charger and cable for any visible damage - if the damage can be seen then lets go forward to step 4- Replace the cable or charger if you see any fraying cuts or bent parts Alternatively, use a different compatible Geek Bar charger with a compatible cable. If it does charge normally with your new setup then the fault lies with the original charger or cable.
2-2 Charging Port Issues
Geek Bar charging port problems are common too Dust debris or moisture in the charging port it can prevent a proper connection between the charger and the device. Versions equipped with two batteries will not - some of them have the last time stopped, which causes intermittent charging or simply do not charge, which may also cause red eight - time flashing.
Over time lint dust or other small debris can get stuck in the charging port particularly if you carry your Geek Bar in a bag or pocket with other things. If for instance, you use your Geek Bar in a humid environment or if it accidentally gets splashed with water, moisture can also enter the port.
Steps to Clean the Charging Port Use a small dry brush like a toothbrush to gently remove dirt or any visible debris. Be careful not to destroy the easy parts within the port. If you see moisture, let the device dry completely in a warm, dry place before trying to charge it again.
Hardware - Related Faults
3-1 Atomizer Problems
What is the Atomizer of a Geek Bar? Conversely, if the atomizer is incorrect it could make the device unable to work and flash on eight - time red.
A clogged coil is the most common atomizer problem. Over time, e liquid residue can accumulate on the coil, obstructing the proper heating of the e - liquid. This causes a poor vaping experience and might also activate the devices safety protocols causing the red flashing.
Another potential problem may be a faulty atomizer. If the coil has burned out or there is a break in the heating element the atomizer will not work properly. A poor fit can cause problems too, but connections are usually standard, and the misfits don't work at all.
If your Geek Bar has a removable atomizer, you can replace the atomizer. Follow the manufacturers directions for the proper install. If you do replace the atomizer and the problem continues to occur, there could be a more serious hardware problem going on.
3-2 Sensor Malfunctions
Geek Bars have several sensors on board to track different aspects of the running of the device such as temperature battery voltage and airflow. When one of these sensors fail they can send incorrect signals to the device control board resulting in the red eight - time flashing.
For instance, an incorrectly calibrated temperature sensor may register a wrong temperature leading the device to mistakenly conclude that it is overheating when it is not. This may trigger the devices safety features and display the warning signal.
Without specialized equipment, diagnosing sensor malfunctions can be difficult. But if you think there's a sensor problem, you could attempt resetting the device (if applicable). It is worth highlighting that some Geek Bar models can actually be reset by a particular combination of button presses. Other times, it requires a reset of the device, which is a good thing to try for any minor issues with sensor glitches. The fixes above may help but if the issue continues it might be better to call the dealer's customer service department or take the device to a professional for repairs.
E - Liquid - Related Concerns
4-1 Low E - Liquid Level
While not as popular a cause of the red eighttime flash as the other issues listed above a low e - liquid level can also instigate this warning. Certain Geek Bar models are equipped with the functionality of sensing when the e - liquid level has dipped to a dangerously low amount and may flash a warning light as a means of prompting the user to refill.
If you have been using your Geek Bar for a while without refilling the e liquid, it may be the fact that the level is too low. D and check the e - liquid reservoir whether be refilled. If the reservoir is low, slowly add the appropriate e - liquid based on the manufacturers' recommendations. But if the red eight - time blinking remains after a refill, the problem will probably be with something else.
4-2 Incompatible E - Liquid
Using a different e - liquid with Geek Bar is also one of the causes of Geek Bar problems. E - liquids come with different nic content compositions viscosities. This means that the Geek Bar is not taking in the right e - liquid and this can cause your Geek Bar to flash red eight times.
For instance high viscosity e - liquids never flow through the device properly leading to an atomizer dry - burn. This can cause damage to the atomizer and set off the warning signal. Thus inaccurate e - liquids with unsuitable nicotine concentrations might not necessarily be dangerous, however it can be if these concentrations are not appropriate for the device used.
You have to use e - liquors always recommended by the Geek Bar manufacturer to avoid this problem. Simply put, if you have changed to a new e - liquid a little while ago, and started to notice this red eight - time flashing, try going back to a known - good e - liquid and see if the issue goes away.
Flashing red eight time on your Geek Bar and you cannot figure out if the issue is because of charging and battery or hardware and e- liquid. Ideally through troubleshooting each step methodically you may greatly enhance your chances of pinpointing and correcting the problem.
When you tried all above and still If red eight - time flashing remain then you will need to contact the manufacters customer support. And they have the knowledge and tools to give more information assistance and can help you find a solution or have your device repaired or purchased. Many of these issues can be avoided in the first place by ensuring proper maintenance and using the device according to the manufacturers specifications.
Table of Contents Review
Battery - Related IssuesCharging - Related Problems
Hardware - Related Faults
E - Liquid - Related Concerns
